Plaster works Works shtukatura Shtukaturu Shtukaturu for work

Panels "-хъюЁю="

IS DECORATIVE

Panels "-хъюЁю=" are made on a basis gipsokartonnyh sheets which industrially paste over from a face sheet with a polyvinylchloride film or polyvinylchloride materials on a paper basis. These vysokodekorativnye panels go on furnish of administrative premises.

Conditions for furnish carrying out "-хъюЁю=юь" - building readiness of buildings, temperature and vlazhnostnyj the mode, preparation of surfaces - remain the same, as at use usual gipsokartonnyh sheets.

Under sheets "-хъюЁю=" put wooden skeletons. Vertical bruski it is necessary to put on distance which depends on width of available sheets. The industry lets out in their width 400, 500 600, mm.

At brick walls under bars put wooden stoppers - 3... 4 pieces depending on wall height but so that between them there were not less than 500 mm. Apertures under stoppers should be depth 6... 8 see nail up bars to stoppers.

To concrete walls bars can be shot down djubeljami.

If there are deviations on a vertical, under bars hammer in wooden wedges, which krepjat to bars nails.

Vertical and horizontal bars should form an equal skeleton. For this purpose in places of their future crossing in advance cut grooves and bars lay down against each other zapodlitso. Connect them on nails.

The Moscow dressers wooden skeletons do a little differently {fig. 106). Having prepared surfaces and having marked installation sites of elements of a skeleton, put horizontal bars section 40X25 mm with step of 600 mm, which krepjat screws to preliminary established wooden stoppers. We sing in places of joining of two adjacent panels establish vertical inserts from a wooden bar of the same section.

the Scheme of facing of walls panels "-хъюЁю=" and asbestotsementnymi sheets on a wooden skeleton: 1 - the panel "-хъюЁю=" or asbestotsementnyj sheet; 2 - a polyvinylchloride or aluminium apportion; 3 - a wooden skeleton from bars section 40x25 mm; in - width of the panel, sheet

a Fig. 106. The scheme of facing of walls panels "-хъюЁю=" and asbestotsementnymi sheets on a wooden skeleton :
1 - the panel "-хъюЁю=" or asbestotsementnyj sheet; 2 - a polyvinylchloride or aluminium apportion; 3 - a wooden skeleton from bars section 40x25 mm; in - width of the panel, sheet

To a skeleton screws krepjat apportions ie rigid polyvinylchloride.

Besides Muscovites use two more kinds of a skeleton: a skeleton from strips gipsokartonnogo sheet and the mixed skeleton from strips gipsokartonnogo sheet with wooden inserts.

The Device of a skeleton from strips GKL is similar to a skeleton which use for facing of walls gipsokartonymi sheets, only here the step of vertical elements another - it should correspond to width of sheet "-хъюЁю=".

Strips GKL for a skeleton are pasted on a wall on gipsoopilochnoj to mastic. Panels "-хъюЁю=" paste to a skeleton on plaster or sulfitno-plaster mastic with a backlash between sheets 5... 6 mm. In a seam on glue "¤хЁьшэшф" insert a polyvinylchloride apportion.

On fig. 107 is presented the mixed skeleton from strips GKL and wooden inserts.

the Scheme of facing of walls panels "-хъюЁю=" and asbestotsementnymi sheets on the mixed skeleton: 1 - a skeleton from strips GKL; 2 - gipsoopilochnaja mastic; 3 - wooden inserts in the size 100x40x25 mm; 4 - sulfatno-plaster mastic; 5 - a polyvinylchloride or aluminium apportion; 6 - the panel "-хъюЁю=" or asbestotsementyj sheet

a Fig. 107. The scheme of facing of walls panels "-хъюЁю=" and asbestotsementnymi sheets on the mixed skeleton :
1 - a skeleton from strips GKL; 2 - gipsoopilochnaja mastic; 3 - wooden inserts in the size 100x40x25 mm; 4 - sulfatno-plaster mastic; 5 - a polyvinylchloride or aluminium apportion; 6 - the panel "-хъюЁю=" or asbestotsementyj sheet

In the mixed skeleton of strip GKL glue on gipsoopilochnoj to mastic. Wooden inserts in the size 100X40x25 in places of joining of horizontal and vertical elements of a skeleton paste mm on sulfitno-plaster mastic. Then to wooden inserts on screws krepjat polyvinylchloride apportions.

To Cut panels "-хъюЁю=" it is necessary seldom. Usenki and luzgi close special apportions. Only at furnish of high premises when the sheet height is insufficient, it is necessary to put the second row on a wall. In this case preparations on a table mark and cut nozhovkoj. Necessary apertures do by rotation or the drilling machine.

Sheets to a skeleton do not beat. Beat (if a skeleton wooden) or paste glue "¤хЁьшэшф" (if a skeleton from strips GKL) special apportions from rigid polyvinylchloride (fig. 108). They happen ordinary, angular and face.

Apportions from rigid polyvinylchloride: and - ordinary; - angular; in - face

a Fig. 108. Apportions from rigid polyvinylchloride :
And - ordinary; - angular; in - face

Begin facing always from a door and conduct in both parties. At a doorway (on such distance that then the sheet edge has been closed by a door platband) establish a face apportion and in it push panel edge. On other edge put an ordinary apportion dvutavrovogo sections and krepjat it to a skeleton. The following panel push in a free groove of an ordinary apportion. Take the following ordinary apportion and operation repeats, will not reach yet a room corner (fig. 109). Having pushed the panel in last on given styoje an ordinary apportion, the worker puts on an angular apportion which together with the same apportion on the adjoining panel forms a right angle closing luzgu or usenok a free end face of the panel. At facing of walls by panels in two ranks on height sheets get in two established apportions - vertical and horizontal.

Fastening of polyvinylchloride apportions in corners: 1 - a wall or a partition; 2 - screws; 3 - a skeleton; 4 - the panel "-хъюЁю="; 5 - a polyvinylchloride apportion

a Fig. 109. Fastening of polyvinylchloride apportions in corners :
1 - a wall or a partition; 2 - screws; 3 - a skeleton; 4 - the panel "-хъюЁю="; 5 - a polyvinylchloride apportion

Panels "-хъюЁю=" store in a premise with air temperature not more low 10°Р and humidity not above 70%. Put them flatwise on the equal firm basis. Size, to drawing, colour. Panels of type I … III stack in pairs a face sheet inside. For panels of type IV between their obverse surfaces it is necessary to lay a paper.

The stack Height should not exceed 1300 mm.